Metrology
Metrology
The Digital Caliper as Swiss Army Knife
EN-US

The Digital Caliper as Swiss Army Knife
George Schuetz, Mahr Federal Inc.


The Swiss Army knife has been around for over 100 years. It's an invaluable collection of tools and accessories that can get you by in an emergency. The tools may not be as good as their single purpose counterparts, but when you've got that special bottle of wine out in the countryside and there isn't a corkscrew around for 15 miles, that odd little one stored in your little Swiss Army Knife is worth its weight in gold.

The same can be said of the Universal Digital Caliper. This caliper is more than a standard caliper, as it has the ability to accessorize itself with a host of special contacts to expand its measuring capability.

We all know the four basic measurements we can make with a caliper: outside, inside, depth, and step measurements. You can do these with just about any Vernier, dial, or digital caliper—kind of like a run-of-the-mill pocket knife. But when the caliper is digital, you can take these measurements one step further and do some of the arithmetic required for compound measurements.

By using this feature and technique on adjacent bores, for example, it's possible to measure one bore, zero the gage on this bore, and then—using the same inside diameter jaws—measure the distance between the far surfaces of the two adjacent bores and have the caliper calculate the center distance between the two bores.

Need to make a shaft or pin to fit an existing bore? Or are you boring a cylinder to fit a piston? You can use your electronic caliper to read the size difference directly.
Use the inside jaws to measure the diameter of the bore. Before you remove the caliper from the bore, press the button to zero the caliper. Now use the outside jaws to measure the shaft. A positive reading (no minus sign displayed) shows that the shaft is larger than the bore. A negative reading (the minus sign appears to the left of the digits) shows that the shaft is smaller than the hole and will fit. The caliper shows you how much material you will need to remove from either the shaft or the bore to make them fit.

When you need to put a bore in a work piece that does not go all the way through, you might want to know how much material remains between the bottom of the bore and the other side of the work piece. Your electronic caliper can display this distance for you.
First use the outside jaws to measure the total thickness of the work piece. Before you remove the caliper from the work piece, press the button to zero the caliper while it is still set to the thickness of the work piece.

Now use the depth rod to measure the depth of the bore. The caliper reading (shown as a negative number) is the remaining thickness between the bottom of the bore and the other side of the work piece.

All of these checks can be performed by your everyday digital caliper, the basic shop tool. But have you ever seen those super duper Swiss Army knives that are loaded with a host of extra tools such as scissors, ballpoint pens, magnifying glass—or now even with USB sticks? These knives have tools that can do just about anything!

Well, the same is just about true of the Universal Digital Caliper. The Universal Digital Caliper has the ability to mount optional contacts within its standard measuring jaws that increase the tool's versatility. Got a groove in a part less than 0.080" in width? A standard caliper would have a tough time making this OD measurement. No problem for the Universal Caliper. Just whip out the special blade contacts, snap them into place, and you're good to go. Have a similar check but on an ID? Well there's an anvil set for that, too, specially made with a thin blade and radiused tip. Snap these into place and the ID becomes just another measurement. Even if the groove is less than 0.020" wide and less then 0.060" deep, it can be measured with the tools in the caliper's bag of accessories.

In a pinch and need to measure some gears or threads? Purpose built gages for these measurements are very precise and quite costly. But say you have a special job, making only a few or a wide variety of gear-like parts which have an even number of teeth, and you can't justify that special gaging. Just get the standard accessories for the Universal Caliper and start making gear checks with the proper ball diameter as called for. Quick, easy and cost effective. The same goes for thread checking. Those same high precision measuring kits used on some precision comparative gages can be adapted to the Universal Caliper, easily adapting it for that emergency measurement.

Maybe the end results won't be as good as uncorking that special wine, but to your boss you may look pretty good nonetheless.


  
The Universal caliper looks just about like any other caliper with its ID and OD jaws. What makes it different is the ability to interchange special contacts into the jaw which greatly expands its capabilities

 



Special radiused contacts, specific size balls, blade anvils or thread anvils can be used to get into some tight measurement locations.